My first shower

Yes - I'm a dirty bugger - this is my first shower ever. M'lady's water heater died yesterday so there was no hot water last night. Thus, this morning I went to the bus to get my shower equipment. I could have showered in the bus but as the shower base is being used to store screws etc, I didn't venture use the shower in the bus. Mind, I also need to install a shower curtain.

The good - I had a shower and managed to wash my hair, my body and came out clean. 

The bad - the shower unit is new (only been used once for testing) yet the hinge on the battery compartment has broken already. The hose connection from the pump unit to the output hose leaks pretty well.
  
I wasn't really expecting to have to fix the shower unit on its first real use. Thank goodness I didn't pay Amazon's rip-off price for it. I paid $18 rather than $35 because I bought mine on eBay. Same exact thing that Amazon charges more for. Having said that, duct tape is cheap and fixed the problem. I think a more permanent solution will be to put an external battery compartment.

It doesn't look elegant but it works which is the main thing. For the leaky hose connection, I suspect duct tape might not be the best answer. It's too flimsy to crimp the hose too tightly so I suspect the best would be to use a piece of soft copper wire and twist it slowly until it's barely tight. There might always be a leak there.

To use the shower, I half-filled my 3 gallon cooler with cold water then put a kettle full of boiling water into it. The result was luke warm - I could definitely do with two kettles of water. Having said that, I did manage to shower quite successfully. The key to good flow seems to be to mnake very sure there are no kinks in the hose. It definitely performed better today - with far more power than when I first tested my shower unit.

Showering like this definitely takes a while as it needs time to boil a kettle of water. The cooker works very well and the floor underneath does not heat much. I'd say the heat transfer is about on a par with the heat from my microwave.

The Coleman cooker cost me $18 from Walmart and the gas cannisters are $3 each. That's really not bad at all. The shower unit was $18 too. 

In terms of use, I used about a gallon and a half of water to shower. My hair is long and takes a while to shower. The key is to wet it, rub shampoo in quickly then work on rinsing it out before proceding to lower parts. Crouching in the shower worked well. Now if I was some bald dude then I can well imagine using maybe a gallon or less of water. I'm not a bald dude though!

I can honestly say that I really quite like this shower setup. I had thought it might be irksome or problematic but it all went together very nicely. The biggest improvement would be for the pump unit and the battery unit to be separated. Now I have seen some 12v versions of this which would work well enough if I had 12v in the bus. Right now, my unit runs off 4 D cells. 

In conclusion, the shower unit's construction quality leaves something to be desired. The efficacy is good. The cooler worked very well and works as a very handy limiter on the amount of water used. The gas cooker was slow and the kettle didn't hold enough water. The shower I had was very effective and quite pleasant though luke warm due to my cooking up only one kettle of water. The cooker needs some while to cool before being put in its box again. I can't imagine lugging the shower and the cooker if I was actually on a backpacking camping expedition but I suppose somebody woud. The nearest alternative is a gas-powered shower unit that costs $140 or over $100 more. This setup represents very good value and I'll keep using it.

The roof

Yesterday I hunted in vain for a tool to use with the compressor to blast the silicone sealant out of the affected seams on the bus. The plan was to use sugar as the blasting compound principally because its more available and cheaper than alternatives.

Proceeding gingerly along the roads, there was little to no sign of flood damage. Indeed, I had to make a detour to see any. Clearly although the flooding has been tragic, the areas I normally visit have been spared. One would not know this, given the constant media coverage. Indeed, I even saw some articulated trucks on the road. Clearly the fears of road instability have been greatly over stated. Indeed this is probably why so many people are ignoring roadblocks.

Visiting store after store, the story was the same at each one. They had grit blasting tools listed but none ever carried in the store despite what the company website claimed. The one place that would have them was Harbor Freight but as visiting them would involve crossing the somewhat suspect Lake Murray dam, I passed on the chance. Instead I shall investigate to see if small areas can be repaired and shall put tape over the affected seams. Maybe after the floods and danger diminish, I can visit Harbor Freight.

The alternative to Harbor Freight is either Northern Tool and a trip across the dam or heating the silicone and scraping it out manually. Had I started that yesterday rather than wasting fuel and hours driving, I could have been done. That would have been today's plan had I not had another fever. It seems I have some kind of rolling virus. I gather others complain of the same virus and how it lasts about a month. That must have been shy yesterday's shopping was do tiring and lackluster.

Today I purchased from eBay a battery powered shower head. The basic plan is to heat water, dump it into my cooler then use that water to shower with. Unlike other shower heads, this one is powered by 4 D cells.

The advantage there is that unlike the rechargeable shower heads with built in batteries, the batteries can be changed. Unlike the 12v plugin shower heads, it runs off a power supply with more possibilities. By that I mean that if I don't have freshly charged D cells, I can use alkaline D cells. Coincidentally, my LED lantern also uses D cells.

That all has me thinking about solar panels to charge AA and D cells. For simple small cell charging, the solar panel need not be gigantic nor expensive. Indeed, 4 D cells might be all that's needed to power my forthcoming front door unlocking system.

Looking at the solar panels available is pretty mind boggling! The whole thing seems vastly complicated. All I want to do is to put a small solar panel on the roof, connect it to a battery charger inside the bus and be done. It's not simple though. As ever, it seems that what I want to do is unusual and not catered toward.

A short term fix for my plumbing came to me this morning. Yesterday while in Walmart I noticed 5 gallon gas cans. My thought is to collect waste water under the bus in a bucket then decant to a 5 gallon gas can for subsequent disposal. For potable water, a few off the shelf camp water containers would work.

Needless to say, these are all inexpensive things that can easily be upgraded at a later stage. Even the cable compartment, rickety as it is, can be upgraded at a later stage. Consideration has to be therefore given to completing the shower plumbing and the interior soft furnishings.

Despite feeling pretty rough, I managed to put a few minutes in, painting the galley floor. It could probably stand more work to attain perfection but it's pretty good. The next thing will be to put a movable vinyl floor covering such as those that protect carpets from mauling by the wheels of swivel chairs.

There are pits and dents in the plywood of the floor. These are due to the plywood the hillbillies laid being of low quality. Still, those sections were in good enough condition not to have to redo which is why they were left. This is probably why they tiled their floor with such disastrous consequences.

Idly I considered visiting the roof. There is an area that needs more grey paint but the paint can is in the middle of the galley workbench which cannot be accessed due to wet paint! Grabbing the ladder, I leaned it against the bus more in hope than anticipation.

As tomorrow is also a non work day, due to the recent floods, I can leave roof stuff until tomorrow. I'll probably just tape the seams with aluminum tape if I can't clearly see any possible leak sites. At least then, it'll all be done. I did look online at a Harbor Freight grit blasting attachment. Online its $17.99 plus $6.99 shipping. Instore it'll likely be the same but a quick calculation showed that gas getting to and from the store was likely to be $4.30 plus a couple of hours time. I think the wear and tear on my car is more than the $2.69 saving. That is, of course, if I opt to clean out the seams instead of taping and painting.

That's what I was going to do. What I really ended up doing was to head to the roof anyway. It took one trip and a look to see the problem. What has happened is rust has lifted the silicone sealant and allowed water underneath.

The three affected seams aren't too bad. It puts paid to my idea of using a wire brush though. I need to get under the seam more than I can with a brush. This looks like it will have to be a grit blaster and the sooner the better! I'll have to hit Harbor Freight tomorrow. For the moment the seams are duct taped against unexpected rain. It looks like I need a lot of rust killing paint and probably some real baking soda since I don't need to blast out silicone. Oddly enough the hard to remove silicone came off easily with a razor blade. I'm glad I caught it before it became too bad. I have no idea what the other seams are really like though they seem OK. The good news is that where I applied rust killer before, without removing any rust, there was very little live rust.