I got me some sugar!

Yup - after spending a rather unproductive time using soda as a blasting medium with my Harbor Freight air blasting tool, I located a small container of sugar that I poured into the blasting head. The difference was immense. I could bring the paint down to bare metal when I needed and managed to roughen the surface of existing paint. 

It is indeed regular cane sugar. The traditional thing to use is sand or preferably silica free sand. Given that sugar is a substance broken down easily by the human body, I'm not too bothered about inhaling minuscule quantities though I hold my breath while I'm blasting. Sand contains silica which causes silicosis - a really nasty and frequently terminal lung ailment. The best thing is sugar is available just about everywhere. A 20lb bag is cheap in Walmart while for sand I'd have to go further and pay more.

Lacking time to paint properly as it was getting close to dusk, I pulled out the first spray can I could locate. Meanwhile, I have been wondering whether I should change the paint scheme. On one hand, I can get grey fairly readily. On the other, I could paint the bus a more interesting color. I'll probably stick with grey on the basis that most of the paint is probably not going to peel. If necessary I can use a steel brush or sandpaper for occasions when the compressor is unavailable. 

One of worries is whether my welds are good enough. I'm going to have to find a real welder and ask his opinion. I think my battery compartment is going to be strong enough. Mind, I've just measured it against a nearby car battery. It seems that the door the hillbillies put on is not large enough to allow a full sized battery. Thus, my plan of using gas seems to be much more of a thing. I can build a smaller cage to hold a small gas container. No need for a huge one as far as I can see. I can get away with a smaller battery because it's not going to be used for powering mains equipment. I'm thinking small electronics such as my tablet and my phone etc.

Speaking of welds, I welded some scrap steel together. This is so that m'lady's niece's boyfriend can his destructive streak and try to destroy it. If he can then I'll have to look harder at my existing welds.
Looking at my bus batteries, they were down to 50% so I put them on charge to bring them back up to 100%. The bus has been sitting idle for months. That's not good for the batteries but one day I'll get around to installing my solar panel. That should keep the battery topped up.

The solar panel I have should keep the bus batteries topped up. I suspect a similar sized panel might be sufficient to provide for my daily electrical needs unless, of course, I decide to install a fridge that runs off 12v. As I've mentioned, I'm experimenting with Peltier elements and these form the basis of 12v fridges. Now a single Peltier would use around 60w or 120ah. To make a freezer, 4 Peltier elements would be needed, using 480ah. That's way in excess of what I'll set up to do. I figure 10-15ah is all I'll likely need if I use gas. Indeed, since my microwave is close to being deceased, it's not too much of a stretch to put a gas hob where the microwave used to be. indeed, I suspect that I might have been better off not installing the 120v setup at all but rather, installing 12v and gas. Having said that, I have what I have. It'll all probably work out for the best. The goal was to have all electric and while that is possible, it's not of immediate financial practicality.

Frustrations

Today started with my laying conduit on the ground from the outside breaker box to where I was going to have my plugin. Then I was going to erect a stake for the socket. The plan was to have the electrics completely done today but as with plans, little was actually accomplished.

The blower swiftly removed fallen leaves and the conduit was layed over the ground. The next stage will be to insert the cable and bury the conduit. I can certainly do better than the Dish Network people that didn't bother burying their cables. An ants nest was revealed and the scurrying ants blown away too.

When it came to cutting a point on the metal stake intended for use with the outside socket, I hit my first big problem of the day. My angle grinder stopped working. After some tinkering, I gave up on it as a lost cause and zoomed off to buy a new one. They're cheap enough at Harbor Freight for $15.

After returning home with my new angle grinder, I proudly plugged it in and it didn't work. Nothing I did could make it work. Putting it away and cursing Harbor Freight, I pulled out a hacksaw and completed the task. Then I drove the stake into the ground.

By then, the light was beginning to fail but I took another look at the angle grinder and found how to dismantle it properly. It seems one of the carbon brushes on the motor had broken. Looking around as I recall there had been spares, I found some that didn't fit.

Clearly either I found spare brushes for another device or Harbor Freight put the wrong brushes in the box. This is rather disappointing and frustrating!

As tomorrow is a party day, nothing will be done. Friday being shop til you drop day, should be good. Everybody will be out on the roads hunting non existent bargains. A good time not to go to Harbor Freight!

Even without an angle grinder, I can complete my wiring in order to run my welder. I fully intend to be welding by Sunday night!

In other news, the Peltier cooler arrived. The glue that fixes it to cooling vanes arrived a few days ago as did the solar panel to power it. I'm still waiting for the cooling vanes.

I've ordered a long permanent magnet to use with a home made coil for my door opening device. Failing that I did see a likely looking solenoid but I'd rather try building something myself first rather than going to a last resort of buying somebody else's junk.

This bus project is taking longer than anticipated. Were I starting again, I would definitely take a different route. Meanwhile I'll have another hunt for the right carbon brushes. Harbor Freight surely can't have been dumb enough to supply the wrong brushes?