Getting down and dirty

Today was a day of achievement and visible achievement at that! In short, the plumbing under the shower is complete. There is a question as to whether I should perhaps add a jubilee clip on each end of the pex tubing so I probably will, just to be sure.

The nuts on the cable grips were replaced with stop nuts. Getting them off was easy despite the application of Locktite Blue Thread Locker. I had anticipated a struggle given the instructions to heat the screw to 700F to release the Thread Locker. I had to do no such thing. Clearly Thread Locker is a garbage product trading on unsubstantiated claims. It was applied to clean, new bolts and the nuts installed just after the stuff had been poured liberally over the threads. It just didn't stick. This is why I trust stop nuts. They just don't vibrate loose. As it transpired, there was insufficient space on the thread for two nuts so I only had to work on one barrel. The other already has stop nuts.

The next thing was to replace the screws and clean up the excess silicone goop from when I installed the sheet metal over the schoolbus flashers. I ran out of 3/16 steel rivets. I'd been rather overzealous with my fastnings and had clearly put 27 holes in each plate. I'll get more rivets tomorrow.

It looks a little better now. A little less obvious. I didn't feel it was worthwhile to weld though soldering would have been useful had I a functional propane torch. While I was up there I replaced the broken CB aerial. This time, rather than having it vertical, I have angled it slightly in order to lessen the chance of tree branches snapping it off.

Now is getting to be the kind of weather when working under the bus is getting unpleasant. Fortunately I don't have much that is truly essental to do underneath. I had to brush off one tick, swat one mosquito, brush off some ants and a couple of spiders. Right beside the bus were a couple of anthills.

Clearly it is going to get really unpleasant soon. The good news is that I have only two things that need doing under the bus. The first is to redo the hillbilly wiring. Now for that I might just get my mechanic friend involved. As for the other, it's a case of doing the plumbing under the sink into the other barrel. For that I need to get a new sink connector and a 1.5 to 1.25 inch piping adaptor plus some 1.25 inch piping. I found my hole saw makes 1.25 inch holes so it seems better to get cheap piping to fit rather than an expensive hole saw the right size. Of course, under the bus, the piping has to reduce to 0.75 inch tubing as I have a lot of 0.75 and my junction is 0.75. I'll further need another 0.75 to 0.5 pex adaptor. The whole plumbing setup is nonstandard because of different ideas that have cropped up as I have been working.

In some places I have overspent. In other I have had bargains. I'm pleased with the hosepipe valves that I picked up for $2 in Walmart. They are way cheaper than anything Lowes (hiss, spit) had. As there will be no real pressure, they don't even have to be very strong!

I am sure my waste water system will leak though I don't know how much. Some leakage is desirable in order to reduce the need to actively dump the waste water. In actual fact, it's just soapy water used for washing. That's not really dirty. The only problem will be non biodegradable deturgents.

I have been giving thought to carrying freshwater and located a 15 gallon barrel at Walmart for $47. That's quite a bargain when U-Line sells them for $41 with $30 shipping. Either that or a 220 mile drive to the nearest U-Line suplier. At 19mpg and $1.85 a gallon, paying shipping would be cheaper than visiting U-Line. Anyway, the Walmart solution sees best. A manual pump also seems in order. Those seem to be between $20 and $60 with electric pumps coming in even cheaper. An alternative to the pump would be just to draw water from under the bus via one of those handy Walmart $2 faucets.

Right now, the goal is to obtain the supplies needed in order to complete current operations. The back door lower window needs to be replaced with something solid. That will involve welding. In fact, quite a lot of welding and some grinding in order to make it smooth. 

Finally, the front door locking mechanism needs addressing. I have encountered linear actuators that sound interesting though pricey. Currently I'm returning to an old idea using the two electromagnets I bought from China that won't repel anything magnetic. Rather than have them pushing the latch upward, pulling it upward - if they're strong enough. Placement will be ultra critical however.

On the whole though progress is painfully slow, I am happy with what has been achieved thus far. I am looking into some kind of fireproof box to keep important documents safe. By that, I mean passports, insurance, registration and citizenship documents. Sadly, thus far, all I am encountering are pretentious pieces of junk. I am seeing fire proof boxes calling themselves safes and sporting ludicrous things such as combination locks and keypads. How utterly insane! All I need is a fireproof box with a latch. I don't want to fuss about with locks or fiddly trash like combination locks. Most of those alleged safes can be picked up and carried away for later opening or can be quickly opened with an angle grinder or a can opener!

How bloody frustrating is that?

Yup. It's a broken drill bit! Not a wussy little drill bit either. That's 3/16th! I'd been battling to install roller blinds where my existing stick-up blinds had fallen down. The problem was I had to drill through not just inner skin but body skeleton as well. That stuff is hard to drill through!

I'd installed two blinds and was working on the final hole for a third blind when - due to tiredness - I pressed the drill too hard and the bit snapped. Well, that put paid to what I intended to do today. I can probably put the third blind up but the end is secured by a single rivet not by two. Yes, today I was using rivets since I am now totally out of short self-drilling bolts. It makes no odds - the blinds will be pretty secure anyway.

My goal for the weekend had been to install all the blinds, finish installing the main breaker box, install the waste water tanks, fit a method of securing the boxes in the back closet and put a panel over the lower back window. Well, that schedule just got knocked for six! Drilling holes today was such a beastly task that even with a power drill it has taken several hours.

Then, of course, there are all the tools I cannot find since I tidied the bus up and put everything where it is supposed to be. I have to be ready for an inspection at any time to verify that I have a motorhome, not a bus. One of those things was the tool I need in order to change the grinding disk on my angle grinder. Thus the disk could not be changed and I could not use my angle grinder to cut the blinds as I have been doing. Instead I had to use a hacksaw. All stuff that just takes extra time!

Right now it's pollen season so everything outside is covered with pollen. Every footstep kicks up gret clouds of pollen - it's like walking on the moon!

The final window one one side put up the biggest fight imaginable. The drill was skidding all over the place. Talk about rock hard steel! Eventually I had one hole in situ. Then after a long hunt, I found just one solitary rivet. I ran out of rivets!

Still, the three blinds I put up look pretty good. There're two more to replace but oddly enough, those stick up blinds have not fallen down - yet. I expect they will if left up for very much longer.


So, tomorrow I definitely need to pick up more rivets. I don't think there's much danger of my proceeding further than putting up the other two blinds and installing the main breaker box.  I'd like to install the underbody waste water tanks and install something to control the boxes stored in the back closet. I have a vague idea that bungee cords might help there but anchor points will be the challenge.

Another thing I'd like to do is to replace the lower rear window or at the very least to cover it on the inside. I could simply bolt or rivet the cover over the window. Replacing the window would be the best option but also the most time consuming. There's an awful lot of welding involved there!

Tomorrow I could buy the stuff to mount my underbody tanks though I have a feeling it won't be needed or used for a while. I know I need to replace my CB aerial too.

The shakedown!

A first run or a shakedown run is so called because you watch for things that fall off as the vehicle shakes. Today, what with fuel prices beginning to rise, I took the bus out to put some more fuel in the tank. I put about 20 gallons of diesel in and that almost filled the tank. Today was the first run the bus has had since probably January of last year. It showed - accelleration and gear changing was sluggish but improved as time went by. It clearly needs a 1000 mile run to get it back into running order.

The gaugues all looked healthy even though the hillbillies buggered around with the rev counter wiring so they could fit a reversing horn (badly). Often the rev counter and occasionally the speedometer don't work because of their bad wiring work. That's all on the list of things to get my mechanic to fix.

A few things fell down when I was driving - mostly things that had been poorly situated such as boxes placed on top of the bed and big boxes piled on top of small boxes in the closet area. My lamp standard toppled too. I'm not in the slightest worried about any of those things. Of more concern were by S hooks. A lot of my S hooks vibrated loose and fell off the screw eyes. Some have fallen into crevices and will be hard to locate. My closet chain was one such casualty of the S hooks. Clearly I need to replace all my S hooks with carabiner clips instead. That's well worth knowing.

On a more serious note, the allegedly flexible CB aerial snagged a low-hanging twig as I was driving off the property and snapped off just above the base. Clearly it wasn't as flexible as claimed. Obviously I need some kind of whip aerial.

Today I put up the shower curtains and found I need to get a 3rd curtain in order to surround the shower fully.  As with the S hooks elsewhere, the S hooks in the bathroom were problematic. I think I'm going to have to buy a lot of small caribiner clips. Evil Bay is probably my best bet there. Failing that, for the closet chain and the shower curtains I suppose I could get stainless steel split rings. That would definitely work but might not be strong enough for clothing.

Otherwise, I spent my time cleaning the inside of the bus and putting things in boxes ready for a series of photos to send to the DMV in the retitling process. The electrics work and aren't a problem unless the power supply has a higher amperage than my cable in which case it's remotely possible to burn out the cable.

These are exterior images.





Thinking about the top flashers, I might just remove them and replace them with aluminum plate riveted in place with silicone sealant. I don't strictly need extra lighting. Rewiring them would represent an interesting issue too. As I go along with this project I become more enamored of simplicity. It might be worth replacing the arrow indicators with the amber covers that have been used on the upper flashers.

The cockpit of the bus looks pretty nice. I do need to revive the original drivers fan though.
 

Moving back, the first compartment is the galley. As my microwave committed suicide, I have no microwave to display so I put a simple set up of a kettle with my $18 gas cooker and some tea bags.
 
 
Going further back, there is the bathroom with no handbasin but a jug and bowl. It's very reminiscent of the 18th century but works pretty well.
 
 
I couldn't step back far enough without falling out of the bus to photograph the shower. My jacket is indeed hnging from one of my S hooks but was heavy enough that the S hook didn't bounce out of place. Moving back is the bedroom with the bedroom table shown in the image. Look very carefully and you can see my camera that - it's a 3 megapixel Canon S1 IS from 2001. Oddly enough my phone takes far better photos so that camera is never used.
  

As can be seen, the bedroom is a bit of a dumping ground for clothes and general junk. I'll have to sift through and get rid of the stuff I don't actually need. For some strange reason I have a box filled with several years of rent receipts and another couple of boxes full of receipts and tax records for a business that I had many years ago that proved tp be a financial nightmare.

Beyond the white door is a simple closet area in which I have a pile of empty plastic totes.

Driving the bus was quite interesting. As I said, it hasn't been driven since January so it's not yet in its prime. The 10 miles or so I put on it today was nothing. I almost took it to a further filling station because the local one was advertised at $1.95 though was actually $1.89. The further filling station was $1.69. I'd probably have used a gallon to get there and a gallon back. 25 gallons would havebeen $5 cheaper but I'd have used half of it on the run so though I was $2 poorer for using the local filling station, I felt safer using the bus on a shorter run given the amount of time it has been standing idle.

On an earlier trip today (in my car), I picked up some supplies to complete the shower curtain (which was achieved) and some supplies to help me finish the plumbing. The most important thing, the heavy chain, I completely omitted to buy! Having said that, I can always use nylon cargo strap either initially or permanently.