Getting down and dirty

Today was a day of achievement and visible achievement at that! In short, the plumbing under the shower is complete. There is a question as to whether I should perhaps add a jubilee clip on each end of the pex tubing so I probably will, just to be sure.

The nuts on the cable grips were replaced with stop nuts. Getting them off was easy despite the application of Locktite Blue Thread Locker. I had anticipated a struggle given the instructions to heat the screw to 700F to release the Thread Locker. I had to do no such thing. Clearly Thread Locker is a garbage product trading on unsubstantiated claims. It was applied to clean, new bolts and the nuts installed just after the stuff had been poured liberally over the threads. It just didn't stick. This is why I trust stop nuts. They just don't vibrate loose. As it transpired, there was insufficient space on the thread for two nuts so I only had to work on one barrel. The other already has stop nuts.

The next thing was to replace the screws and clean up the excess silicone goop from when I installed the sheet metal over the schoolbus flashers. I ran out of 3/16 steel rivets. I'd been rather overzealous with my fastnings and had clearly put 27 holes in each plate. I'll get more rivets tomorrow.

It looks a little better now. A little less obvious. I didn't feel it was worthwhile to weld though soldering would have been useful had I a functional propane torch. While I was up there I replaced the broken CB aerial. This time, rather than having it vertical, I have angled it slightly in order to lessen the chance of tree branches snapping it off.

Now is getting to be the kind of weather when working under the bus is getting unpleasant. Fortunately I don't have much that is truly essental to do underneath. I had to brush off one tick, swat one mosquito, brush off some ants and a couple of spiders. Right beside the bus were a couple of anthills.

Clearly it is going to get really unpleasant soon. The good news is that I have only two things that need doing under the bus. The first is to redo the hillbilly wiring. Now for that I might just get my mechanic friend involved. As for the other, it's a case of doing the plumbing under the sink into the other barrel. For that I need to get a new sink connector and a 1.5 to 1.25 inch piping adaptor plus some 1.25 inch piping. I found my hole saw makes 1.25 inch holes so it seems better to get cheap piping to fit rather than an expensive hole saw the right size. Of course, under the bus, the piping has to reduce to 0.75 inch tubing as I have a lot of 0.75 and my junction is 0.75. I'll further need another 0.75 to 0.5 pex adaptor. The whole plumbing setup is nonstandard because of different ideas that have cropped up as I have been working.

In some places I have overspent. In other I have had bargains. I'm pleased with the hosepipe valves that I picked up for $2 in Walmart. They are way cheaper than anything Lowes (hiss, spit) had. As there will be no real pressure, they don't even have to be very strong!

I am sure my waste water system will leak though I don't know how much. Some leakage is desirable in order to reduce the need to actively dump the waste water. In actual fact, it's just soapy water used for washing. That's not really dirty. The only problem will be non biodegradable deturgents.

I have been giving thought to carrying freshwater and located a 15 gallon barrel at Walmart for $47. That's quite a bargain when U-Line sells them for $41 with $30 shipping. Either that or a 220 mile drive to the nearest U-Line suplier. At 19mpg and $1.85 a gallon, paying shipping would be cheaper than visiting U-Line. Anyway, the Walmart solution sees best. A manual pump also seems in order. Those seem to be between $20 and $60 with electric pumps coming in even cheaper. An alternative to the pump would be just to draw water from under the bus via one of those handy Walmart $2 faucets.

Right now, the goal is to obtain the supplies needed in order to complete current operations. The back door lower window needs to be replaced with something solid. That will involve welding. In fact, quite a lot of welding and some grinding in order to make it smooth. 

Finally, the front door locking mechanism needs addressing. I have encountered linear actuators that sound interesting though pricey. Currently I'm returning to an old idea using the two electromagnets I bought from China that won't repel anything magnetic. Rather than have them pushing the latch upward, pulling it upward - if they're strong enough. Placement will be ultra critical however.

On the whole though progress is painfully slow, I am happy with what has been achieved thus far. I am looking into some kind of fireproof box to keep important documents safe. By that, I mean passports, insurance, registration and citizenship documents. Sadly, thus far, all I am encountering are pretentious pieces of junk. I am seeing fire proof boxes calling themselves safes and sporting ludicrous things such as combination locks and keypads. How utterly insane! All I need is a fireproof box with a latch. I don't want to fuss about with locks or fiddly trash like combination locks. Most of those alleged safes can be picked up and carried away for later opening or can be quickly opened with an angle grinder or a can opener!