A week or so back I ordered some bolts for my drawers. Today they arrived and mightily stout they are too. Way better than I'd expected and far cheaper than the flimsier versions I was considering earlier. I'm very happy! They'll need a piece of hardboard behind them in order to center the bolt in the drawer but that's not a problem. These things are stout and will hold my drawers closed even if an elephant is trying to break out!
For those with short memories, these are the bolts. I took a photo today but for some unknown reason my phone couldn't achieve correct focus. It wasn't worth digging out a camera and a laptop just for a single photo!
I had a good hunt through the junk I removed from the bus to see if I could find an appropriate nut for the shower waste pipe but they were either too big or two small. With my luck, this will be some bizarre size nobody has ever heard of. Danco, the manufacturer, refused to supply a further nut even though I was willing to pay money and postage. Lowe's who weren't helpful in the store suddenly decided to make a show of helping online (for publicity) but that so far has achieved nothing worthwhile.
The economy must be booming with nobody unemployed any more if companies can afford to turn business away! Clearly my eyes must be deceiving me when I see people begging beside the road, banks repossessing homes and people being thrown out of their homes.
The nut needed is probably an oddball size. I measured the pipe at 1.48 inches on the outside of the threads and 1.45 inches on the inside of the threads. Clearly this is either going to be an undersized 1.5 inch thing or something wacky like 37 or 38 millimeters.
My big gripe about US plumbing is that just about everything is a non standard size. Even two allegedly identically sized things can be way off identical. This is probably why the hillbillies that converted the bus the first time around, gave up!
I did discover a specialist plumbing supply company not far away. It's probably worth paying them a visit. They might even be able to supply something better of a more standard size.
Looking at the heavy angle iron that I have, I'll need something stout to secure that to the bus. Being as heavy as it is, I might be well advised to use rivets rather than bolts. Clearly my little hand riveter isn't up to the task of using rivets the size needed. Thus, after being astounded at the cost of electric and air riveters, I saw a riveter powered by .22 cartridges. It's more expensive in operation but given the small amount of riveting needed, could well work out cheaper. Welding would be the best solution but as I've never welded, now's not a good time to try.
The plan with the cable compartment is to rebuild it properly. I'll probably house one or if possible, two batteries in it. One would be ample to power things like fans and USB power supplies etc. I might visit the scrapyard for some stouter materials.
For those with short memories, these are the bolts. I took a photo today but for some unknown reason my phone couldn't achieve correct focus. It wasn't worth digging out a camera and a laptop just for a single photo!
I had a good hunt through the junk I removed from the bus to see if I could find an appropriate nut for the shower waste pipe but they were either too big or two small. With my luck, this will be some bizarre size nobody has ever heard of. Danco, the manufacturer, refused to supply a further nut even though I was willing to pay money and postage. Lowe's who weren't helpful in the store suddenly decided to make a show of helping online (for publicity) but that so far has achieved nothing worthwhile.
The economy must be booming with nobody unemployed any more if companies can afford to turn business away! Clearly my eyes must be deceiving me when I see people begging beside the road, banks repossessing homes and people being thrown out of their homes.
The nut needed is probably an oddball size. I measured the pipe at 1.48 inches on the outside of the threads and 1.45 inches on the inside of the threads. Clearly this is either going to be an undersized 1.5 inch thing or something wacky like 37 or 38 millimeters.
My big gripe about US plumbing is that just about everything is a non standard size. Even two allegedly identically sized things can be way off identical. This is probably why the hillbillies that converted the bus the first time around, gave up!
I did discover a specialist plumbing supply company not far away. It's probably worth paying them a visit. They might even be able to supply something better of a more standard size.
Looking at the heavy angle iron that I have, I'll need something stout to secure that to the bus. Being as heavy as it is, I might be well advised to use rivets rather than bolts. Clearly my little hand riveter isn't up to the task of using rivets the size needed. Thus, after being astounded at the cost of electric and air riveters, I saw a riveter powered by .22 cartridges. It's more expensive in operation but given the small amount of riveting needed, could well work out cheaper. Welding would be the best solution but as I've never welded, now's not a good time to try.
The plan with the cable compartment is to rebuild it properly. I'll probably house one or if possible, two batteries in it. One would be ample to power things like fans and USB power supplies etc. I might visit the scrapyard for some stouter materials.
No comments:
Post a Comment