Looking at the whiz-bang thermometer gizmo in my bus, I noted that the 102 degrees farenherit combined with 60% humidity might have been the reason for my frequent breaks. I'd work and do very little then I'd be drenched in sweat. Each time I worked, it was like having a mini shower - in sweat!
Despite the heat and a mini thunderstorm, I managed to complete most of what I set out to achieve today. I put fronts on all of my drawers. What I didn't get around to was retarding one drawer about half an inch still there's always tomorrow!
The first drawer front went on and I managed to install it a shade too low and a little crooked.
After that I put the one above straight. Now the reason I got it crooked was that I couldn't find my pre-drilled holes due to my putting glue over them. With later drawers I was careful to avoid covering the holes with glue.
It's a little redneck but I found my way of spacing drawer fronts was easiest using a pair of carpenter's pencils. I'd put them on top of the drawer front below and then just rest the next drawer front on them and wiggle it to the right position before drilling my holes. A piece oif plywood offcut leaned against the drawer front as I worked helped a lot.
As can be seen from the photos, I used a lot of drywall screws. These were used rather than clamping everything together. That really sped things up. I'd drill the holes, take the drawer out and place it on a workbench then apply glue, put screws through the fascia and locate them in the holes on the drawer then screw it together. I'd start with just two locating screws then add more as needed to squeeze the wood together. And the glue I used was Elmers. It seems to have worked well!
Finally, I had all the drawer fronts in place. The bottom left drawer could do with some trimming of the fascia tomorrow. I knocked off after this because I felt I had done well today and didn't want to push my luck and mess something up.
In the dinette/kitchenette, my remaining tasks are hinges for 3 cupboard doors, handles on 3 cupboard doors and 8 drawers, catches on the drawers and doors, painting the drawers, ceiling and floor, privacy film on the windows, painting the door and construction of my saloon doors. There's even sufficient plywood left over for the bedroom table!
Despite the heat and a mini thunderstorm, I managed to complete most of what I set out to achieve today. I put fronts on all of my drawers. What I didn't get around to was retarding one drawer about half an inch still there's always tomorrow!
The first drawer front went on and I managed to install it a shade too low and a little crooked.
After that I put the one above straight. Now the reason I got it crooked was that I couldn't find my pre-drilled holes due to my putting glue over them. With later drawers I was careful to avoid covering the holes with glue.
It's a little redneck but I found my way of spacing drawer fronts was easiest using a pair of carpenter's pencils. I'd put them on top of the drawer front below and then just rest the next drawer front on them and wiggle it to the right position before drilling my holes. A piece oif plywood offcut leaned against the drawer front as I worked helped a lot.
As can be seen from the photos, I used a lot of drywall screws. These were used rather than clamping everything together. That really sped things up. I'd drill the holes, take the drawer out and place it on a workbench then apply glue, put screws through the fascia and locate them in the holes on the drawer then screw it together. I'd start with just two locating screws then add more as needed to squeeze the wood together. And the glue I used was Elmers. It seems to have worked well!
Finally, I had all the drawer fronts in place. The bottom left drawer could do with some trimming of the fascia tomorrow. I knocked off after this because I felt I had done well today and didn't want to push my luck and mess something up.
In the dinette/kitchenette, my remaining tasks are hinges for 3 cupboard doors, handles on 3 cupboard doors and 8 drawers, catches on the drawers and doors, painting the drawers, ceiling and floor, privacy film on the windows, painting the door and construction of my saloon doors. There's even sufficient plywood left over for the bedroom table!
No comments:
Post a Comment